China Meper View Strip Plastic Blow Moulding Machine For 1 Gallon Pesticide Bottles

View strip Plastic Blow Molding Machine for pesticide bottle for 1 gallon container

 

Brief introduction

 

Features:

 

1. Structure design front and back is a complete set, no welding, heavy structure design make sure machine no any viberation when in production

2. Linear guide support the Carriage up down and clamping,reduce the friction between tie-bar and bushes,extend the life of machine.

3. Self-lubricated Copper bush used in all the moving point,make machine working more faster

and stable

4. Carriage up and down speed control valve installed,make sure machine working in high speed but no any noise and shake.

5. Linear transducer and stroke switch installed for better control and safety control

6. A return oil cycle design in the nose part of oil cylinder rod to avoid any leakage possibility

7. Automatic center lubrication system ,controller can set the lubrication time and frequency

8. Platform manually adjusted up and down,die head have twin-cylinder design

9. Fast response PLC control system, easy operating, endurable

10. Each hydraulic circuit can be controlled separately

11. 30L accumulator air tank installed for stable the blow air pressure and flow

12. Micro parison thickness adjustment along with micro blow pin center adjustment are controlled by 3-4bolt,easy for operator

13. Whole cooling system water pipe are using Oil pipe, longer life and remain low temperature

14. Material loading gate and material level sensor is installed,can connect with auto-loader

15. Mould lifting crane is optional for easier mould installation

 

Machine specification:

 

MP80D-1T-5LAYER7/70/35/35/25)

5 Layer single head with View strip optional

 

(1).Extrusion unit

1. Main screw:70mm with L/D:24/1 Screw RPM:15-60R.P.M

1) Heating zone:3zones Heating power:10.8KW

2) 2 Fan zones,Temperature can be individually controlled by PLC interface

3) extrusion motor size:18.5KW

4) Adopt Rexroth-Germany inverter ,size 18.5KW

5) Gearbox adopt top 3 China brand Yuyuan,model:ZLYJ-200

6) Main screw is using for the outer layer, thickness accounting 42.5%

 

2. First layer screw:70mm with L/D:24/1 Screw RPM:15-60R.P.M

1) Heating zone:3zones Heating power:10.8KW

2) 2 Fan zones,Temperature can be individually controlled by PLC interface

3) Adopt Rexroth-Germany inverter ,size 18.5KW

4) Gearbox adopt top 3 China brand Yuyuan,model:ZLYJ-200

5) first layer after the outer layer,thickness accounting 42.5%

 

3. Adhensive screw:35mm with L/D:24/1 Screw RPM:15-60R.P.M

1) Heating zone:3zones Heating power::2.2KW

2) 1 Fan zones,Temperature can be individually controlled by PLC interface

3) Adopt Rexroth-Germany inverter ,size 2.2KW

4) Gear box using direct connection design more accurate and powerful

5) Adhensive located in Second and fourth layer,each layer thickness accounting:5%

 

4. EVOH layer Screw diameter:35mm L/D ratio:24/1 Screw RPM:15-60R.P.M

1) heating zone:3zones Heating power:2.2KW

2) 1 Fan zones,Temperature can be individually controlled by PLC interface

3) Adopt Rexroth-Germany inverter ,size 2.2KW

4) Gear box using direct connection design more accurate and powerful

5) EVOH between 2 layer adhensive ,accounting 5%

 

5．View strip screw size:25mm L/D:24/1 Screw RPM:15-60R.P.M

1) heating zone:3zones Heating power:1.6KW

2) 1 Fan zones,Temperature can be individually controlled by PLC interface

 

(2) Die head

1. Number of Head:Single

2. Type:FIFO

3. Heating zone:3,heating power:10KW

4. Die (Thickness)adjustment:4 Bolt adjustment

5. Material:38CrMoAlA,Cr12MoV

6. Hydraulic cylinder diameter for MOOG:120mm,stroke:20mm

 

(3) Clamping unit

1 Mould height:465mm,Mould width:520mm

2. Platen stroke:220-620mm.

3. clamping foce:150KN(15Ton,140kgf/cm2)

4. Locking cylinder diameter:120mm stroke:450mm

5. carriage cylinder diameter: 50mm stroke:540mm

6. Carriage moving type:Tie-bar and linear.

7. Locking Supporting arm,Hook,Copper platen balance ring using for strengthing

8. Self-lubricated Copper bush using for all the moving part

9. Planten width:420mm

10 . Platen height:465mm

 

(4) Blowing unit

1. Blow pin oil cylinder diameter:40mm stroke:150mm

2. pre-blow,multi-blow function can be optional

3. Blow pin tip cooling system

4. Blow pin center system is easiest micro control by 3 front bolt

5. Blow pin down

 

(5) Cutter

1. Type:Hot cutter(straight cut)

2. Cutter cylinder dia:40mm,Stroke:200mm.

3. Dimmer model:2000VA

4. Supporting by 2 copper pole

5. Cutter wiring is using100m²anti-high temperature specialized type.

(protecting by plastic tube)

6. Cuting blade material:High grade stainless steel

 

(6) Hydraulic system

1. Pump motor:11KW

2. Hydraulic motor brand:Vickers-American

3. Hydaulic oil tank size:250L

4. Hydraulic valve and components: Vickers-American

5. MOOG hydraulic tank separate unit

 

(7) Cooling ystem

 

1. Hydraulic cooling inlet size:1cinch

2. Mould cooling water main inlet size:1inch

3. Mould water pipe connect to mainifoild size: Φ12mm

4. Cooling water consumption:40L/min

5. Condernsor model:GLD-2.1

 

(8) Compression air system

1. Main air inlet size: Φ16mm

2. Air consumption:6-8Mpa , 1.2m³/min

3. 30L separately accumulator air tank installed for better stability of air

5. pheumatic valve model:Φ750.

5. Bottom defleshing pheumatic valve model:Φ740

6. Blow flow and supporting air can be adjust in the front panel

 

(9) Structure

 

1. Platform:manual up and down stroke:100mm

2. Oil cylinder diameter for up and down:40mm stroke:35mm

3. Micro balance adjustment system installed in both side of the platform

4. Machine weight:10T

5. Machine installed both hanging Hook and bottom fork-car for easier loading.

 

(10) Electronics

1. Techmation controller newtest version-Taiwan

2. 8inch color screen,USB drive installed for easier upgrade the program version

3. individually thickness control system Moog

4. Carriage down stop position installed Scheinider stroke switch

5. IML is optional

6.Total power:86KW

 

(11) Safety

1. Orange-red color paint for the platen .

2. Operating door got a limited switch, when Open the door, electric cut.

3. Safty sensor and stopping pole installed, when anything entering will immediately stop electric.

4. Over heated alarm

5. Temperature inter-lock system ,when barrel haven’t reach the setting temperature, extrusion motor can not drive to protect the screw of damaged.